You are here: Home > Installation Instructions for Fontana Lenox Automatic Soap Dispenser Commercial Gold Wall Mount Automatic Foam Auto Soap Dispenser

How to install Fontana Lenox Automatic Soap Dispenser Commercial Gold Wall Mount Automatic Foam Auto Soap Dispenser | FS9801G


Easy step by steps installation instructions for Commercial Sensor Soap Dispenser
Visit Product Page
  • Before you begin, please read the installation instructions below. Observe all local building and safety codes.
  • Unpack and inspect the products for any shipping damages. If you find damages, do not install.
  • Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
sensor


Automatic Soap Dispenser Installation Instructions







Front ViewsensorSide View



Step 1:sensorStep 2:


Step 3:Step 4:


Step 5:Step 6:


Step 7:Step 8:


Step 9:Step 10:


Step 11:Step 12:


Step 13:Step 14:


Driving Type:Sensor
Dia. of Inlet:DN15 (G1/2')
Installing Hole:35mm
Body Material:59 Brass
Finished:Chrome Plating
Power Input:AC220V
Water Pressure:0.05 - 0.7 MPa
Static Consumption:≤ 50uA
Dynamic Consumption:500mA
Work time:1.5s (Ajustable)
Drops:0.5-1.5ml (Ajustable)
Induction distance:10±2cm (Adjustable)



1. The dispenser is mounted directly to the wall above the basin. The control box is mounted below the basin and the soap tube and sensor connector are run through the wall behind the basin and back out the front of the wall to the control box below the basin.

2. Remove the escutcheon from the dispenser assembly by unscrewing counter-clockwise. Correctly orient the dispenser and mark the holes.

3. Remove the two retention screws and remover the body from the base. Drill 3/16" holes on the marks and insert anchors. Attach the base to the wall using the supplied screws

4. Feed the soap tube and sensor connector through the wall and reattach the body to the base by tightening the retention screws.

5. Reinstall the escutcheon by threading it clockwise onto the base.

Note: It is recommended to horizontally offset the soap dispenser spout with the faucet 4 - 6” and to install vertically 6-10" above the sink drain at the same height as the faucet. To comply with ADA standards, the center-point of the soap dispenser spout must be less than 50" from the finished floor.

Soap fill and Startup
1. Remove the soap bottle from the control box by unscrewing the soap bottle counter-clockwise. Fill the soap bottle with soap of the appropriate viscosity. Do not overfill the soap bottle.

2. Re-attach the soap bottle to the control box, making sure that the soap input tube is inside the soap bottle. Depress the green system prime button until soap comes from the nozzle. The system is now ready to use.

CARE AND MAINTENANCE
If the soap dispenser fails to function correctly, firstly check all connections are tight and free from air leaks. If dispenser still fails to function, place manifold into a bottle of warm water. Pump the warm water through the dispenser to dislodge any dried soap residue and then refit manifold into soap bottle.

Water marks and soap residue on polished chrome surfaces are best cleaned using warm water and a mild detergent. Use a stainless steel cleaner for brushed stainless steel soap dispensers. Never use an abrasive cloth to remove stubborn stains. Dry with a soft clean cloth.

ALWAYS mount the soap tank feeding the dispenser/s BELOW the level of the dispensers

NEVER mount the soap tank feeding the dispenser/s ABOVE the level of the dispensers

Also please note:
The soap type and brand used in these dispensers should not be altered throughout the life of the dispenser as mixing soaps can affect their chemical characteristics and cause them to become more aggressive. If another soap type or brand is needing to be used then the previous type must be thoroughly flushed through and cleaned from the soap dispensers and system prior to its use.












CARE AND MAINTENANCE - General Instructions



















1. Fill the soap bottle with soap for the first use.
2. Press and hold the button until soap is dispensed from the nozzle.
3. Place hand below the nozzle to dispense soap into the palm of hand.


CARE AND MAINTENANCE
If the soap dispenser fails to function correctly, firstly check all connections are tight and free from air leaks. If dispenser still fails to function, place manifold into a bottle of warm water. Pump the warm water through the dispenser to dislodge any dried soap residue and then refit the manifold into the soap bottle.

Watermarks and soap residue on polished chrome surfaces are best cleaned using warm water and a mild detergent. Use a stainless steel cleaner for brushed stainless steel soap dispensers. Never use an abrasive cloth to remove stubborn stains. Dry with a soft clean cloth.

ALWAYS mount the soap tank feeding the dispenser/s BELOW the level of the dispensers

NEVER mount the soap tank feeding the dispenser/s ABOVE the level of the dispensers

Also please note:
The soap type and brand used in these dispensers should not be altered throughout the life of the dispenser as mixing soaps can affect their chemical characteristics and cause them to become more aggressive. If another soap type or brand is needing to be used then the previous type must be thoroughly flushed through and cleaned from the soap dispensers and system prior to its use.


Fontana Lenox Automatic Soap Dispenser Commercial Gold Wall Mount Automatic Foam Auto Soap Dispenser


The Fontana Lenox automatic soap dispensers sanitary is a Commercial Wall Mount Motion Sensor Automatic Foam Soap Dispenser which can dispense the soap efficiently has a shing gold body finish. All in one sensor design and with 0.39gal (1500ml)capacity soap container can pump out soap right after sensed by the sensor eye. Use multi-voltage power supply, suitable for input voltage between AC 100V-240V,and it can meet the requirement of different projects. It saves soap, water, and time as well. This touchless motion sensor faucet reduces the transfer of germs by preventing cross-contamination and re-contamination of germs and bacteria by not touching the faucets or handles. It cut down on water usage by minimizing waste of water while soaping, lathering, scrubbing by eliminating unnecessary and unattended water flow. Convenient to maintain with built-in strainer to prevent sundries from entering the solenoid valve and the strainer is easy to clean. Ideal for commercial use applications in public restrooms, restaurants, office building, public facilities, hospitals. Fits all US standard plumbing.

Features:

Visit Product Page
  • Brand Name: Fontana
  • Model Number: FS9801G
  • Material: Brass
  • Finish: Gold
  • Type: Automatic Foam Soap Dispenser
  • Capacity: 0.39gal(1500ml)
  • Usage: Bathroom, Washing, Public Place
  • Installation: Wall mount
  • Application: Bathroom foam soap dispenser
  • Size: 5.7*4.13*1.96 inches (145x105x50mm)
  • Power supply: DC 6V
  • Function: Anti-bacteria
  • Usage: Residential / Commercial





FontanaSensorFaucets® Product Warranty Information FontanaSensorFaucets Product Warranty
Installation Instructions for Fontana Verona Cold & Hot Gold Finish Touchless Bathroom Faucet

Shower & Faucet Installation Instructions